Notice: Trying to get property 'slug' of non-object in /nas/content/live/cdiver/wp-includes/taxonomy.php on line 4233

SATURATION DIVING

0
254

Saturation diving is a diving technique that allows divers to avoid the deadly effects of “the bends” so they can work at great depth for long periods of time.

For diving operations below 50m, a mixture of helium and oxygen (heliox) is required to eliminate the narcotic effect of nitrogen under pressure. For extended diving operations at depth, saturation diving is the preferred approach. A saturation system would be installed within the Offshore Supply Vessel. A diving bell would transport the divers between the saturation system and the work site lowered through a ‘moon pool’ in the bottom of the ship, usually with a support structure ‘cursor’ to support the diving bell through the turbulent waters near the surface. There are a number of support systems for the saturation system on a Diving Support Vessel, usually including a diving bell, a transfer chamber, decompression chamber, launch and recovery systems, winches, reclaim supportequipments, control van

DECOMPRESSION SICKNESS (DCS)

Decompression sickness (DCS) is a potentially fatal condition caused by bubbles of inert gas, which can occur in divers’ bodies following the pressure reduction as they ascend. To prevent DCS, divers have to limit their rate of ascent, and pause at regular intervals to allow the pressure of gases in their body to approach equilibrium. This protocol, known as decompression stops, can last for many hours for dives in excess of 50 metres (160 ft) when divers spend more than a few minutes at these depths. The longer divers remain at depth, the more inert gas is absorbed into their body tissues, and the time required for decompression increases rapidly. This presents a problem for operations that require divers to work for extended periods at depth. However, after a few hours under pressure, divers’ bodies become saturated with inert gas, and no further uptake occurs. From that point onward, no increase in decompression time is necessary. The idea of saturation diving takes advantage of this by providing a means for divers to remain at depth for days. At the end of that period, divers need to carry out a single decompression schedule, which is much more efficient than making multiple short dives, each of which requires a lengthy decompression time.

SAT SYSTEM ELEMENTS

A SAT system can be permanently placed on a Vessel of Opportunity (VOO), but is more commonly capable of being moved from one vessel to another. The entire system is managed from a control room (van), where depth, chamber atmosphere and other system parameters are monitored and controlled. The diving bell is the elevator or lift that transfers divers from the system to the work site. Typically, it is mated to the system utilizing a removable clamp and is separated from the system tankage bulkhead by a trunking space, a kind of tunnel, through which the divers transfer to and from the bell. At the completion of work or a mission, the saturation diving team is decompressed gradually back to atmospheric pressure by the slow venting of system pressure, at an average of 15metres (49 ft) per day, traveling 24 hours a day (schedules vary). Thus the process involves only one ascent, thereby mitigating the time-consuming and comparatively risky process of in-water, staged decompression normally associated with non-saturation (“mixed gas diving or sur-D O2″) operations.

The divers use surface supplied umbilical diving equipment, utilizing deep diving breathing gas, such as helium and oxygen mixtures, stored in large capacity, high pressure cylinders. The gas supplies are plumbed to the control room, where they are routed to supply the system components. The bell is fed via a large, multi-part umbilical that supplies breathing gas, electricity, communications and hot water. The bell also is fitted with exterior mounted breathing gas cylinders for emergency use.

While in the water the divers use a hot water suit to protect against the cold. The hot water comes from boilers on the surface and is pumped down to the diver via the bell’s umbilical and then through the diver’s umbilical.

Source

LEAVE A REPLY

Please enter your comment!
Please enter your name here

This site uses Akismet to reduce spam. Learn how your comment data is processed.